"levelsof may hit the limits imposed by your Stata. However, it is
typically used when the number of distinct values of varname is modest."
(from -h levelsof-). I should have anticipated this problem. Are the levels
of your "a" in any way regularly spaced (to enable application of
-forvalues-)?
HTH
Martin
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Carlo Lazzaro
Sent: Tuesday, October 14, 2008 12:44 PM
To: [email protected]
Subject: st: how to work around -levelsof- limits with Stata 9.2/SE?
Dear Statalisters,
I have performed successfully Martin's helpful syntax using -levelsof- on a
sample of 20 distinct values for var a.
However, when I tried to repeat the loop for the total 10,000 levels of var
a I got an error message(admittedly, the recommended limit for -levelsof- is
a modest number of distinct values for varlist, so I cannot complain about
this useful ado.file). Is there any way to work this around?
Please find below the command lines I typed along with the error message I
got at the end of the sequence:
. levelsof ICER_round, loc(levels) *around 10,000 levels are still
reported after rounding to the nearest whole number
. foreach lev of local levels {
2. g result`lev'=` ICER_round'* Delta_Q- Delta_C
3. }
invalid syntax
r(198);
Thanks a lot for your kindness and for your time.
Kind Regards,
Carlo
-----Messaggio originale-----
Da: [email protected]
[mailto:[email protected]] Per conto di Carlo Lazzaro
Inviato: martedì 14 ottobre 2008 11.46
A: [email protected]
Cc: 'Martin Weiss'
Oggetto: st: R: RE: a possible - foreach - question?
Dear Martin,
thanks a lot for your precious hint. It works perfectly.
Thanks a lot again and Kind Regards,
Carlo
-----Messaggio originale-----
Da: [email protected]
[mailto:[email protected]] Per conto di Martin Weiss
Inviato: martedì 14 ottobre 2008 11.04
A: [email protected]
Oggetto: st: RE: a possible - foreach - question?
***************+
sysuse auto, clear
*get the levels of mpg (a in your xmpl)
levelsof mpg, loc(levels)
*loop through them, create new vars along the way
*price takes place of b in your code, headroom is c
foreach lev of loc levels{
g result`lev'=`lev'*price- headroom
}
*get the means from -summarize-
su result*
***************
HTH
Martin
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Carlo Lazzaro
Sent: Tuesday, October 14, 2008 10:50 AM
To: [email protected]
Subject: st: a possible - foreach - question?
Dear Statalisters,
I have three variables (a; b; C with 10,000 observations each) in long
format.
For each value of a I would like to obtain the following one:
(a1 * b1) - c1
.
.
.
.
(a1*b10,000)-c10,000;
Repeat the above reported would-be 10,000 times (i.e., from a1 to a10,000)
Create a new variable d in which the mean of each one of the 10,000
iterations are stored and can be displayed.
I suppose there's way of doing this with Stata 9.2/SE, but I cannot figure
out the proper syntax.
Thanks a lot for your kindness and for your time.
Kind Regards,
Carlo
*
* For searches and help try:
* http://www.stata.com/help.cgi?search
* http://www.stata.com/support/statalist/faq
* http://www.ats.ucla.edu/stat/stata/
*
* For searches and help try:
* http://www.stata.com/help.cgi?search
* http://www.stata.com/support/statalist/faq
* http://www.ats.ucla.edu/stat/stata/
*
* For searches and help try:
* http://www.stata.com/help.cgi?search
* http://www.stata.com/support/statalist/faq
* http://www.ats.ucla.edu/stat/stata/
*
* For searches and help try:
* http://www.stata.com/help.cgi?search
* http://www.stata.com/support/statalist/faq
* http://www.ats.ucla.edu/stat/stata/
*
* For searches and help try:
* http://www.stata.com/help.cgi?search
* http://www.stata.com/support/statalist/faq
* http://www.ats.ucla.edu/stat/stata/
